View MC33696_1157204.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Freescale Semiconductor Data Sheet
MC33696 Rev. 9, 06/2007
MC33696
PLL Tuned UHF Transceiver for Data Transfer Applications
1
Overview
GNDSUBD
The MC33696 is a highly integrated transceiver designed for low-voltage applications. It includes a programmable PLL for multi-channel applications, an RSSI circuit, a strobe oscillator that periodically wakes up the receiver while a data manager checks the content of incoming messages. A configuration switching feature allows automatic changing of the configuration between two programmable settings without the need of an MCU.
LQFP32
QFN32
STROBE
SWITCH
VCC2IN
2
Features
RSSIOUT VCC2RF RFIN GNDLNA VCC2VCO GNDPA1 RFOUT GNDPA2 1 2 3 4 5 6 7 8
32
31
30
29
28
27
26
25 24 23 22 21 20 19 18 17
General: * 304 MHz, 315 MHz, 426 MHz, 434 MHz, 868 MHz, and 915 MHz ISM bands * Choice of temperature ranges: -- -40C to +85C -- -20C to +85C * OOK and FSK transmission and reception * * * * 20 kbps maximum data rate using Manchester coding 2.1 V to 3.6 V or 5 V supply voltage Programmable via SPI 6 kHz PLL frequency step
GNDIO
VCCIN
GND
NC
SEB SCLK MOSI MISO CONFB DATACLK RSSIC GNDDIG
10
11
12
13
14
VCCDIG
VCC2OUT
RBGAP
15
9
XTAL0UT
(c) Freescale Semiconductor, Inc., 2006, 2007. All rights reserved.
VCCINOUT
VCCDIG2
XTALIN
GND
16
Features
*
*
Current consumption: -- 13.5 mA in TX mode -- 10.3 mA in RX mode -- Less then 1 mA in RX mode with strobe ratio = 1/10 -- 260 nA standby and 24 A off currents Configuration switching -- allows fast switching of two register banks
Receiver: * -106.5 dBm sensitivity, up to -108 dBm in FSK 2.4 kbps * Digital and analog RSSI (received signal strength indicator) * Automatic wakeup function (strobe oscillator) * Embedded data processor with programmable word recognition * * * Image cancelling mixer 380 kHz IF filter bandwidth Fast wakeup time
Transmitter: * Up to 7.25 dBm output power * Programmable output power * FSK done by PLL programming Ordering information
Temperature Range -40C to +85C -20C to +85C QFN Package MC33696FCE/R2 MC33696FCAE/R2 LQFP Package MC33696FJE/R2 MC33696FJAE/R2
MC33696 Data Sheet, Rev. 9 2 Freescale Semiconductor
Pre Regulator VCCIN
RSSI_8BITS
VCCINOUT
Freescale Semiconductor
Analog Test ANALOG_SIGNALS Logarithmic Amplifier RSSI 4 Bits A/D Strobe Oscillator V&I Reference Voltage Regulator VCC2OUT VCC2IN RBGAP STROBE TEST_CONTROL ACCLNA PMA + I/Q Image Reject 1.5 MHz, BW 400 kHz AGC GAIN_SET AGC_CONTROL FM-to-AM Converter DATA_RATE AGC_CONTROL FM_AM SWITCH_TESTOUT State Machine IF Amplifier Detector Analog Data Filter and Slicer Rx Data Manager SPI MOSI MISO SCLK SEB RSSIC BAND BAND IF_REF_CLOCK PFD XCO Clock Generator DATACLK DIG_CLOCK XTALOUT XTALIN VCCDIG Fractional Divider FREQUENCY_12BITS MODULATION Tx Data Manager Voltage Regulator VCCDIG2 CONFB GND GND GNDDIG GNDIO GNDSUBD GNDSUBA /2 VCO PA SLOPE_&_POWER_CONTROL
RSSIOUT_TESTIN
SWITCH_TESTOUT
VCC2RF
RFIN
LIN +I/Q Mixers
GNDLNA
Figure 1. Block Diagram
MC33696 Data Sheet, Rev. 9
VCC2VC0
/2 or Buffer
VCC2RF
RFOUT
GNDPA1
GNDPA2
Features
3
Pin Functions
3
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Pin Functions
Table 1. Pin Functions
Name RSSIOUT VCC2RF RFIN GNDLNA VCC2VCO GNDPA1 RFOUT GNDPA2 XTALIN XTALOUT VCCINOUT VCC2OUT VCCDIG VCCDIG2 RBGAP GND GNDDIG RSSIC DATACLK CONFB MISO MOSI SCLK SEB GNDIO VCCIN NC STROBE GNDSUBD VCC2IN SWITCH GND RSSI analog output 2.1 V to 2.7 V internal supply for LNA RF input Ground for LNA (low noise amplifier) 2.1 V to 2.7 V internal supply for VCO PA ground RF output PA ground Crystal oscillator input Crystal oscillator output 2.1 V to 3.6 V power supply/regulator output 2.1 V to 2.7 V voltage regulator output for analog and RF modules 2.1 V to 3.6 V power supply for voltage limiter 1.5 V voltage limiter output for digital module Reference voltage load resistance General ground Digital module ground RSSI control input Data clock output to microcontroller Configuration mode selection input Digital interface I/O Digital interface I/O Digital interface clock I/O Digital interface enable input Digital I/O ground 2.1 V to 3.6 V or 5.5 V input No connection Strobe oscillator capacitor or external control input Ground 2.1 V to 2.7 V power supply for analog modules for decoupling capacitor RF switch control output General ground Description
MC33696 Data Sheet, Rev. 9 4 Freescale Semiconductor
Silicon Version
4 5
Silicon Version Maximum Ratings
Table 2. Maximum Ratings
Parameter Symbol VCCIN VCC VCC2 -- VCCPA VCCIO -- -- -- TS TJ Value VGND-0.3 to 5.5 VGND-0.3 to 3.6 VGND-0.3 to 2.7 VGND-0.3 to VCC2 VGND-0.3 to VCCINOUT+2 VGND-0.3 to VCCIN+0.3 2000 200 260 -65 to +150 150 Unit V V V V V V V V C C C
This data sheet describes the functional features of silicon version ES4.1.
Supply voltage on pin: VCCIN Supply voltage on pins: VCCINOUT, VCCDIG Supply voltage on pins: VCC2IN, VCC2RF, VCC2VCO Voltage allowed on each pin (except RFOUT and digital pins) Voltage allowed on pin: RFOUT Voltage allowed on digital pins: SEB, SCLK, MISO, MOSI, CONFB, DATACLK, RSSIC, STROBE ESD HBM voltage capability on each pin1 ESD MM voltage capability on each Solder heat resistance test (10 s) Storage temperature Junction temperature NOTES: 1 Human body model, AEC-Q100-002 rev. C. 2 Machine model, AEC-Q100-003 rev. C. pin2
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 5
Power Supply
6
Power Supply
Table 3. Supply Voltage Range Versus Ambient Temperature
Temperature Range1 Parameter Symbol -40C to +85C -20C to +85C 2.1 to 3.6 4.5 to 5.5 3.0 to 3.6 V V V VCC3V VCC5V VCCPA 2.7 to 3.6 4.5 to 5.5 3.0 to 3.6 Unit
Supply voltage on VCCIN, VCCINOUT, VCCDIG for 3 V operation Supply voltage on VCCIN for 5 V operation Supply voltage on VCCPA for 3 V or 5 V operation NOTES: 1 -40C to +85C: MC33696FCE/FJE. -20C to +85C: MC33696FCAE/FJAE.
The circuit can be supplied from a 3 V voltage regulator or battery cell by connecting VCCIN and VCCINOUT. It is also possible to use a 5 V power supply connected to VCCIN; in this case VCCINOUT should not be connected to VCCIN. The RFOUT pin cannot be biased with a voltage higher than 3.6 V. For 5 V operation, biasing voltage is available on VCCINOUT. An on-chip low drop-out voltage regulator supplies the RF and analog modules (except the strobe oscillator and the low voltage detector, which are directly supplied from VCCINOUT). This voltage regulator is supplied from pin VCCINOUT and its output is connected to VCC2OUT. An external capacitor must be inserted between VCC2OUT and GND for stabilization and decoupling. The analog and RF modules must be supplied by VCC2 by externally wiring VCC2OUT to VCC2IN, VCC2RF and VCC2VCO.
MC33696 Data Sheet, Rev. 9 6 Freescale Semiconductor
Supply Voltage Monitoring and Reset
VCC2 32 31 30 29 28 27 26 25
3V
VCC2 32 31 30 29 28 27 26 25
5V
SWITCH
VCC2IN
GNDSUBD
STROBE
GNDIO
GND
VCCIN
SWITCH
VCC2IN
GNDSUBD
STROBE
1 VCC2 2 3 4 VCC2 5 6 7 8
RSSIOUT VCC2RF RFIN GNDLNA
SEB SCLK MOSI
24 23 22 21 20 19 18 17 VCC2 VCC2
GNDIO
GND
VCCIN
NC
NC
1 2 3 4 5 6 7 8
RSSIOUT VCC2RF RFIN GNDLNA
SEB SCLK MOSI
24 23 22 21 20 19 18 17
VCC2VCO GNDPA1 VCCINOUT RFOUT XTAL0UT GNDPA2 XTALIN
U11 MC33696
MISO CONFB DATACLK RSSIC
VCC2VCO GNDPA1 VCCINOUT RFOUT XTAL0UT GNDPA2 XTALIN
U11 MC33696
MISO CONFB DATACLK RSSIC
VCC2OUT
VCC2OUT
VCCDIG2
VCCDIG2
VCCDIG
GNDDIG RBGAP GND
VCCDIG
GNDDIG RBGAP GND
9
10
11
12
13
14
15
16
9
10
11
12
13
14
15
VCC2
VCC2
3V Operation
5V Operation
Figure 2. Wiring Diagrams
A second voltage regulator supplies the digital part. This regulator is powered from pin VCCDIG and its output is connected to VCCDIG2. An external capacitor must be inserted between VCCDIG2 and GNDDIG, for decoupling. The supply voltage VCCDIG2 is equal to 1.6 V. In standby mode, this voltage regulator goes into an ultra-low-power mode, but VCCDIG2 = 0.7 x VCCDIG. This enables the internal registers to be supplied, allowing configuration data to be saved.
7
Supply Voltage Monitoring and Reset
At power-on, an internal reset signal is generated. All registers are reset. When the LVDE bit is set, the low-voltage detection module is enabled. This block compares the supply voltage on VCCINOUT with a reference level of about 1.8 V. If the voltage on VCCINOUT drops below 1.8 V, status bit LVDS is set. The information in status bit LVDS is latched and reset after a read access. NOTE If LVDE = 1, the LVD module remains enabled. The circuit cannot be put in standby mode, but remains in LVD mode with a higher quiescent current, due to the monitoring circuitry. LVD function is not accurate in standby mode.
8
Receiver Functional Description
The receiver is based on a superheterodyne architecture with an intermediate frequency (IF) of 1.5 MHz (see Figure 1). Its input is connected to the RFIN pin. Frequency down conversion is done by a high-side
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 7
16
Transmitter Functional Description
injection I/Q mixer driven by the frequency synthesizer. An integrated poly-phase filter performs rejection of the image frequency. The low intermediate frequency allows integration of the IF filter providing the selectivity. The center frequency is tuned by automatic frequency control (AFC) referenced to the crystal oscillator frequency. Sensitivity is met by an overall amplification of approximately 96 dB, distributed over the reception chain, comprising low-noise amplifier (LNA), mixer, post-mixer amplifier, and IF amplifier. Automatic gain control (AGC), on the LNA and the IF amplifier, maintains linearity and prevents internal saturation. Sensitivity can be reduced using four programmable steps on the LNA gain. Amplitude demodulation is achieved by peak detection and comparison with a fixed or adaptive voltage reference selected during configuration. Frequency demodulation is achieved in two steps: the IF amplifier AGC is disabled and acts as an amplitude limiter; a filter performs a frequency-to-voltage conversion. The resulting signal is then amplitude demodulated in the same way as in the case of amplitude modulation with an adaptive voltage reference. A low-pass filter improves the signal-to-noise ratio. Shaped data are available if the integrated data manager is not used. If used, the data manager performs clock recovery and decoding of Manchester coded data. Data and clock are then available on the serial peripheral interface (SPI). The configuration sets the data rate range managed by the data manager and the bandwidth of the low-pass filter. An internal low-frequency oscillator can be used as a strobe oscillator to perform an automatic wakeup sequence. It is also possible to define two different configurations for the receiver (frequency, data rate, data manager, modulation, etc.) that are automatically loaded during wakeup or under MCU control. If the PLL goes out of lock, received data are ignored.
9
Transmitter Functional Description
The single-ended power amplifier is connected to the RFOUT pin. In the case of amplitude modulation, coded data sent by the microcontroller unit (MCU) are used for on/off keying (OOK) the RF carrier. Rise and fall times of the RF signal are controlled to minimize spurious emission. In the case of frequency modulation, coded data sent by the MCU are used for frequency shift keying (FSK) the RF carrier. RF output power can be reduced using four programmable steps. Out-of-lock detection prevents any out-of-band emission, by stopping the transmission. The logic output SWITCH enables control of an external RF switch for isolating the two RF pins. Its output toggles when the circuit changes from receive to transmit, and vice versa.
MC33696 Data Sheet, Rev. 9 8 Freescale Semiconductor
Frequency Planning
10
Frequency Planning
10.1 Clock Generator
All clocks running in the circuit are derived from the reference frequency provided by the crystal oscillator (frequency fref, period tref). The crystal frequency is chosen in relation to the band in which the MC33696 has to operate. Table 4 shows the value of the CF bits.
Table 4. Crystal Frequency and CF Values Versus Frequency Band
RF Frequency (MHz) 304 315 426 433.92 868.3 916.5 CF1 CF0 LOF1 LOF0 FREF (Crystal Frequency) (MHz) 16.96745 17.58140 23.74913 24.19066 24.16139 25.50261 FIF (IF Frequency) (MHz) 1.414 1.465 1.484 1.512 1.510 1.594 Dataclk Divider 60 60 80 80 80 80 Fdataclk (kHz) 282.791 293.023 296.864 302.383 302.017 318.783 Digclk Divider 30 30 40 40 40 40 Fdigclk (kHz) 565.582 586.047 593.728 604.767 604.035 637.565 Tdigclk (s) 1.77 1.71 1.68 1.65 1.66 1.57
0 0 0 0 1 1
0 0 1 1 1 1
0 1 0 0 0 1
0 0 1 1 1 1
10.2 Intermediate Frequency
The IF filter is controlled by the crystal oscillator to guarantee the frequency over temperature and voltage range. The IF filter center frequency, FIF, can be computed using the crystal frequency fref and the value of the CF bits: * If CF[0] = 0 : FIF = fref/9*1.5/2 * If CF[0] = 1 : FIF = fref/12*1.5/2 The cut-off frequency given in the parametric section can be computed by scaling to the FIF.
Example 1. Cut-off Frequency Computation
Compute the low cut-off frequency of the IF filter for a 16.9683 MHz crystal oscillator. For this reference frequency, FIF = 1.414 MHz. So, the 1.3751 MHz low cut-off frequency specified for a 1.5 MHz IF frequency becomes 1.3751*1.414/1.5 = 1.296 MHz
10.3 Frequency Synthesizer Description
The frequency synthesizer consists of a local oscillator (LO) driven by a fractional N phase locked loop (PLL). The LO is an integrated LC voltage controlled oscillator (VCO) operating at twice the RF frequency (for the 868 MHz frequency band) or four times the RF frequency (for the 434 MHz and 315 MHz frequency bands). This allows the I/Q signals driving the mixer to be generated by division.
1. Refer to parameter 3.3 found in Section 19.1, "General Parameters." MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 9
Register Access through SPI
The fractional divider offers high flexibility in the frequency generation for: * Switching between transmit and receive modes. * Achieving frequency modulation in FSK modulation transmission. * Performing multi-channel links. * Trimming the RF carrier. Frequencies are controlled by means of registers. To allow for user preference, two programming access methods are offered (see Section 17.3, "Frequency Registers"). * In friendly access, all frequencies are computed internally from the contents of the carrier frequency and deviation frequency registers. * In direct access, the user programs direct all three frequency registers.
11
Register Access through SPI
11.1 SPI Interface
the MC33696 and the MCU communicate via a bidirectional serial digital interface. According to the selected mode, the MC33696 or the MCU manages the data transfer. The MC33696's digital interface can be used as a standard SPI (master/slave) or as a simple interface (SPI deselected). In the latter case, the interface's pins are used as standard I/O pins. However, the MCU has the highest priority, as it can control the MC33696 by setting CONFB pin to the low level. The interface is operated by four I/O pins. * SEB -- Serial interface Enable When SEB is set high, pins SCLK, MOSI, and MISO are set to high impedance. This allows individual selection in a multiple device system, where all devices are connected via the same bus. The rest of the circuit remains in the current state, enabling fast recovery times, but the power amplifier is disabled to prevent any uncontrolled RF transmission. * SCLK -- Serial Clock Synchronizes data movement in and out of the device through its MOSI and MISO lines. The master and slave devices can exchange a byte of information during a sequence of eight clock cycles. Since SCLK is generated by the master device, this line is an input on a slave device. * MOSI -- Master Output Slave Input Transmits bytes when master, and receives bytes when slave, with the most significant bit first. When no data are output, SCLK and MOSI force a low level. * MISO -- (Master Input) Slave Output Transmits data when slave, with the MSB first. There is no master function. Data are valid on falling edges of SCLK. This means that the clock phase and polarity control bits of the microcontroller SPI have to be CPOL = 0 and CPHA = 1 (using Freescale acronyms). Table 5 summarizes the serial digital interface feature versus the selected mode.
MC33696 Data Sheet, Rev. 9 10 Freescale Semiconductor
Register Access through SPI
Table 5. Serial Digital Interface Feature versus Selected Mode (SEB = 1)
Selected Mode Configuration Transmit Receive DME = 1 DME = 0 Standby / LVD MC33696 Digital Interface Use SPI slave, data received on MOSI, SCLK from MCU, MISO is output SPI deselected, MOSI receives encoded data from MCU SPI master, data sent on MOSI with clock on SCLK SPI deselected, received data are directly sent to MOSI SPI deselected, all I/O are high impedance
The data transfer protocol for each mode is described in the following sections.
11.2 Configuration Mode
This mode is used to write or read the internal registers of the MC33696. As long as a low level is applied to CONFB (see Figure 29), the MCU is the master node driving the SCLK input, the MOSI line input, and the MISO line output. Whatever the direction, SPI transfers are 8-bit based and always begin with a command byte, which is supplied by the MCU on MOSI. To be considered as a command byte, this byte must come after a falling edge on CONFB. Figure 3 shows the content of the command byte.
Bit 7 Bit Name N1 Bit 6 N0 Bit 5 A4 Bit 4 A3 Bit 3 A2 Bit 2 A1 Bit 1 A0 Bit 0 R/W
Figure 3. Command Byte
Bits N[1:0] specify the number of accessed registers, as defined in Table 6.
Table 6. Number N of Accessed Registers
N[1:0] 00 01 10 11 Number N of Accessed Registers 1 2 4 8
Bits A[4:0] specify the address of the first register to access. This address is then incremented internally by N after each data byte transfer. R/W specifies the type of operation: 0 = Read 1 = Write Thus, this bit is associated with the presence of information on MOSI (when writing) or MISO (when reading).
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 11
Register Access through SPI
Figure 4 and Figure 5 show write and read operations in a typical SPI transfer. In both cases, the SPI is a slave. A received byte is considered internally on the eighth falling edge of SCLK. Consequently, the last received bits, which do not form a complete byte, are lost. NOTE A low level applied to CONFB does not affect the configuration register contents.
SEB
CONFB SCLK (Input) MOSI (Input) MISO (Output) N1 N0 A4 A3 A2 A1 A0 R/W D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
Figure 4. Write Operation in Configuration Mode (N[1:0] = 01)
SEB
CONFB SCLK (Input) MOSI (Input) MISO (Output) N1 N0 A4 A3 A2 A1 A0 R/W
D7 D6 D5 D4 D3 D2 D1
D0
D7 D6 D5 D4 D3 D2 D1 D0
Figure 5. Read Operation in Configuration Mode (N[1:0] = 01)
11.3 Configuration Switching
This feature allows for defining two different configurations using two different banks, and for switching them automatically during wakeup when using a strobe oscillator, or by means of the strobe pin actuation by the MCU. This automatic feature may be used only in receiver mode; however, if one of the register banks is related to a transmitter configuration, it may be accessed directly by programing some bits to define the active bank, thus allowing fast switching between receiver mode and transmitter mode, or between any different possible configurations.
MC33696 Data Sheet, Rev. 9 12 Freescale Semiconductor
Register Access through SPI
11.3.1 Bit Definition
Two sets of configuration registers are available. They are grouped in two different banks: Bank A and Bank B. Two bits are used to define which bank represents the state of the component.
Bit Name BANKA BANKB BANKA X 0 1 Direction R/W R/W Location Bank A Bank B
BANKB Actions 0 Bank A is active (TX or RX) 1 Bank B is active (TX or RX) 1 Bank A and Bank B are active and will be used one after the other (RX only)
At any time, it is possible to know what is the active bank by reading the status bit BANKS.
Bit Name BANKS Direction R Location Comment A&B Bank status: indicates which register bank is active. This bit, available in Bank A and Bank B, returns the same value.
11.3.2 Bank Access and Register Mapping
Registers are physically mapped following a byte organization. The possible address space is 32 bytes. The base address is specified in the command byte. This is then incremented internally to address each register, up to the number of registers specified by N[1:0], also specified by this command byte. All registers can then be scanned, whatever the type of transmission (read or write); however, writing to read-only bits or registers has no effect. When the last implemented address is reached, the internal address counter automatically loops back to the first mapped address ($00). At any time, it is possible to write or read the content of any register of Bank A and Bank B. Register access is defined as follows: R/W Bit can be read and written. R Bit can be read. Write has no effect on bit value. RR Bit can be read. Read or write resets the value. R [A] Bit can be read, this returns the same value as Bank A. RR [A] Bit can be read, this returns the same value as Bank A. Read or write resets the value.
Table 7. Access to Specific Bits
Bit RESET OLS LDVS SOE RSSIx Bank A A, B A, B A, B A, B Byte CONFIG1 CONFIG3 CONFIG3 CONFIG2 RSSI Access R/W R-R[A] RR-RR[A} R/W-R[A} R-R[A} Available in BANKA. Bit value is the real time status of the PLL, BANKA, and BANKB access reflect the same value. Bit value is the latched value of the low-voltage detector. Read or write from any bank resets value. SOE can be modified in BANKA. Access from BANKB reflects BANKA value. RSSI value is directly read from RSSI converter. Reflected value is the same whatever the active byte. Comment
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 13
Register Access through SPI
14 MC33696 Data Sheet, Rev. 9 Freescale Semiconductor
00h CONFIG1-A Bit 7 Bit Name LOF1 1 Reset Value R/W 0 = 304-434 1 = 315-916 01h CONFIG2-A Bit 7 Bit Name DSREF 0 Reset Value R/W 0 = Fixed 1 = Adaptive 02h CONFIG3-A Bit 7 Bit Name AFF1 0 Reset Value R/W 0 = 0.5-1 kHz 1 = 2-4 kHz 03h COMMAND-A Bit 7 Bit Name AFFC 0 Reset Value R/W 0 = AFFx OFF 1 = AFFx ON 04h F1-A Bit 7 Bit Name FSK3 0 Reset Value R/W 05h F2-A Bit 7 Bit Name F7 0 Reset Value R/W
91 h Bit 6 Bit 5 LOF0 CF1 0 0 R/W R/W 304-315 315-434 434-916 868 10 h Bit 6 Bit 5 FRM MODU 0 0 R/W R/W Friendly OOK Direct FSK 30 h Bit 6 Bit 5 AFF0 OLS 0 1 R/W R 0.5-2 kHz RAS 1-4 kHz Unlocked 9h Bit 6 Bit 5 IFLA MODE 0 0 R/W R/W No RX -20 dB TX 48 h Bit 6 Bit 5 FSK2 FSK1 1 0 R/W R/W 0h Bit 6 Bit 5 F6 F5 0 0 R/W R/W
Bit 4 CF0 1 R/W 314 434-868 Bit 4 DR1 1 R/W 2.4-4.8 9.6-19.2 Bit 4 LVDS 1 RR RAS Low V Bit 4 RSSIE 0 R/W No Yes Bit 4 FSK0 0 R/W Bit 4 F4 0 R/W
Bit 3 RESET 0 R/W No Yes Bit 3 DR0 0 R/W 2.4-9.6 4.8-19.2 Bit 3 ILA1 0 R/W 0-8 dB 14-24 dB Bit 3 EDD 1 R/W Slow dec. Fast dec. Bit 3 F11 1 R/W Bit 3 F3 0 R/W
Bit 2 SL 0 R/W T/R R/T Bit 2 TRXE 0 R/W Standby Enable Bit 2 ILA0 0 R/W 0-14 dB 8-24 dB Bit 2 RAGC 0 R/W No Yes Bit 2 F10 0 R/W Bit 2 F1 0 R/W
Bit 1 LVDE 0 R/W No Yes Bit 1 DME 0 R/W No Yes Bit 1 OLA1 0 R/W 0-8 dB 14-24 dB Bit 1 FAGC 0 R/W No Yes Bit 1 F9 0 R/W Bit 1 F1 0 R/W
0Dh CONFIG1-B Bit 7 Bit Name LOF1 Reset Value 1 R/W 0 = 304-434 1 = 315-916 0Eh CONFIG2-B Bit 0 Bit 7 SOE Bit Name DSREF 0 Reset Value 0 R/W R/W No 0 = Fixed Yes 1 = Adaptive 0Fh CONFIG3-B Bit 0 Bit 7 OLA0 Bit Name AFF1 0 Reset Value 0 R/W R/W 0-14 dB 0 = 0.5-1 kHz 8-24 dB 1 = 2-4 kHz 10h COMMAND-B Bit 0 Bit 7 BANKS Bit Name AFFC 1 Reset Value 0 R R/W B Bank 0 = AFFx OFF A Bank 1 = AFFx ON 11h F1-B Bit 0 Bit 7 F8 Bit Name FSK3 0 Reset Value 0 R/W R/W 12h F2-B Bit 0 Bit 7 F0 Bit Name F7 0 Reset Value 0 R/W R/W Bit 0 CLKE 1 R/W No Yes
91 h Bit 6 Bit 5 LOF0 CF1 0 0 R/W R/W 304-315 315-434 434-916 868 10 h Bit 6 Bit 5 FRM MODU 0 0 R/W R/W Friendly OOK Direct FSK 30 h Bit 6 Bit 5 AFF0 OLS 0 1 R/W R[A] 0.5-2 kHz RAS 1-4 kHz Unlocked 9h Bit 6 Bit 5 IFLA MODE 0 0 R/W R/W No RX -20 dB TX 4800 h Bit 6 Bit 5 FSK2 FSK1 1 0 R/W R/W 0h Bit 6 Bit 5 F6 F5 0 0 R/W R/W
Bit 4 CF0 1 R/W 314 434-868 Bit 4 DR1 1 R/W 2.4-4.8 9.6-19.2 Bit 4 LVDS 1 RR[A] RAS Low V Bit 4 RSSIE 0 R/W No Yes Bit 4 FSK0 0 R/W Bit 4 F4 0 R/W
Bit 3 -- 0 R -- -- Bit 3 DR0 0 R/W 2.4-9.6 4.8-19.2 Bit 3 ILA1 0 R/W 0-8 dB 14-24 dB Bit 3 EDD 1 R/W Slow dec. Fast dec. Bit 3 F11 1 R/W Bit 3 F3 0 R/W
Bit 2 SL 0 R/W T/R R/T Bit 2 TRXE 0 R/W Standby Enable Bit 2 ILA0 0 R/W 0-14 dB 8-24 dB Bit 2 RAGC 0 R/W No Yes Bit 2 F10 0 R/W Bit 2 F1 0 R/W
Bit 1 LVDE 0 R/W No Yes Bit 1 DME 0 R/W No Yes Bit 1 OLA1 0 R/W 0-8 dB 14-24 dB Bit 1 FAGC 0 R/W No Yes Bit 1 F9 0 R/W Bit 1 F1 0 R/W
Bit 0 CLKE 1 R/W No Yes Bit 0 SOE 0 R[A] No Yes Bit 0 OLA0 0 R/W 0-14 dB 8-24 dB Bit 0 BANKS 1 R[A] B Bank A Bank Bit 0 F8 0 R/W Bit 0 F0 0 R/W
Bank A Registers
Bank B Registers
Figure 6. Bank Registers
Freescale Semiconductor MC33696 Data Sheet, Rev. 9 15
06h FT1-A Bit Name Reset Value 07h FT2-A Bit Name Reset Value 08h FT3-A Bit 7 Bit Name FTB7 0 Reset Value R/W 09h RXONOFF-A Bit 7 Bit Name BANKA 0 Reset Value R/W 0Ah ID-A Bit 7 Bit Name IDL1 1 Reset Value R/W 0Bh HEADER-A Bit 7 Bit Name HDL1 1 Reset Value R/W 0Ch RSSI-A Bit 7 Bit Name RSSI7 0 Reset Value R Bit 7 FTA3 0 R/W Bit 7 FTA11 0 R/W
700701 h Bit 6 FTA10 1 R/W 7h Bit 6 FTA2 0 R/W 1h Bit 6 FTB6 0 R/W 75 h Bit 6 RON3 1 R/W C0 h Bit 6 IDL0 1 R/W 80 h Bit 6 HDL0 0 R/W 80 h Bit 6 RSSI6 0 R
13h FT1-B Bit 5 FTA9 1 R/W Bit 5 FTA1 0 R/W Bit 5 FTB5 0 R/W Bit 5 RON2 1 R/W Bit 5 ID5 0 R/W Bit 5 HD5 0 R/W Bit 5 RSSI5 0 R Bit 4 FTA8 1 R/W Bit 4 FTA0 0 R/W Bit 4 FTB4 0 R/W Bit 4 RON1 1 R/W Bit 4 ID4 0 R/W Bit 4 HD4 0 R/W Bit 4 RSSI4 0 R Bit 3 FTA7 0 R/W Bit 3 FTB11 0 R/W Bit 3 FTB3 0 R/W Bit 3 RON0 1 R/W Bit 3 ID3 0 R/W Bit 3 HD3 0 R/W Bit 3 RSSI3 0 R Bit 2 FTA6 0 R/W Bit 2 FTB10 1 R/W Bit 2 FTB2 0 R/W Bit 2 ROFF2 1 R/W Bit 2 ID2 0 R/W Bit 2 HD2 0 R/W Bit 2 RSSI2 0 R Bit 1 FTA5 0 R/W Bit 1 FTB9 1 R/W Bit 1 FTB1 0 R/W Bit 1 ROFF1 1 R/W Bit 1 ID1 0 R/W Bit 1 HD1 0 R/W Bit 1 RSSI1 0 R Bit 0 FTA4 0 R/W Bit 0 FTB8 1 R/W Bit 0 FTB0 1 R/W Bit 0 ROFF0 1 R/W Bit 0 ID0 0 R/W Bit 0 HD0 0 R/W Bit 0 RSSI0 0 R Bit Name Reset Value 14h FT2-B Bit Name Reset Value 15h FT3-B Bit 7 FTB7 0 R/W 16h RXONOFF-B Bit 7 Bit Name BANKB Reset Value 0 R/W 17h ID-B Bit 7 Bit Name IDL1 Reset Value 1 R/W 18h HEADER-B Bit 7 Bit Name HDL1 Reset Value 1 R/W 19h RSSI-B Bit 7 Bit Name RSSI7 Reset Value 0 R[A] Bit Name Reset Value Bit 7 FTA3 0 R/W Bit 7 FTA11 0 R/W
700701 h Bit 6 FTA10 1 R/W 7h Bit 6 FTA2 0 R/W 1h Bit 6 FTB6 0 R/W 75 h Bit 6 RON3 1 R/W C0 h Bit 6 IDL0 1 R/W 80 h Bit 6 HDL0 0 R/W 80 h Bit 6 RSSI6 0 R[A]
Bit 5 FTA9 1 R/W Bit 5 FTA1 0 R/W Bit 5 FTB5 0 R/W Bit 5 RON2 1 R/W Bit 5 ID5 0 R/W Bit 5 HD5 0 R/W Bit 5 RSSI5 0 R[A]
Bit 4 FTA8 1 R/W Bit 4 FTA0 0 R/W Bit 4 FTB4 0 R/W Bit 4 RON1 1 R/W Bit 4 ID4 0 R/W Bit 4 HD4 0 R/W Bit 4 RSSI4 0 R[A]
Bit 3 FTA7 0 R/W Bit 3 FTB11 0 R/W Bit 3 FTB3 0 R/W Bit 3 RON0 1 R/W Bit 3 ID3 0 R/W Bit 3 HD3 0 R/W Bit 3 RSSI3 0 R[A]
Bit 2 FTA6 0 R/W Bit 2 FTB10 1 R/W Bit 2 FTB2 0 R/W Bit 2 ROFF2 1 R/W Bit 2 ID2 0 R/W Bit 2 HD2 0 R/W Bit 2 RSSI2 0 R[A]
Bit 1 FTA5 0 R/W Bit 1 FTB9 1 R/W Bit 1 FTB1 0 R/W Bit 1 ROFF1 1 R/W Bit 1 ID1 0 R/W Bit 1 HD1 0 R/W Bit 1 RSSI1 0 R[A]
Bit 0 FTA4 0 R/W Bit 0 FTB8 1 R/W Bit 0 FTB0 1 R/W Bit 0 ROFF0 1 R/W Bit 0 ID0 0 R/W Bit 0 HD0 0 R/W Bit 0 RSSI0 0 R[A]
Register Access through SPI
Bank A Registers
Bank B Registers
Figure 6. Bank Registers (continued)
Register Access through SPI
11.3.3 Direct Switch Control
The conditions to enter direct switch control are: * Strobe pin = VCC * SOE bit = 0 By simply writing BANKA and BANKB, the active bank will be defined:
BANKA X 0 1 BANKB 0 Bank A is active (TX or RX) 1 Bank B is active (TX or RX) 1 Not allowed in direct switch control
Defined bank is active after exiting the configuration mode, i.e., CONFB line goes high. The direct switch control should be used when: * One or both banks are in transmitter configuration (MODE = 1) * When the strobe oscillator cannot be used to define the switch timing (for example, not periodic) * When strobe pin use is not possible (no sleep mode between the two configurations) * No automatic switching is required and MCU SPI access is possible
11.3.4 Strobe Pin Switch Control
The conditions to enter strobe pin switch control are: * Strobe pin: controlled by MCU I/O port * SOE bit = 0 By simply writing BANKA and BANKB, the active banks will be defined.
BANKA X 0 1 BANKB 0 Bank A is active (TX or RX) 1 Bank B is active (TX or RX) 1 Bank A and Bank B are both active, configuration will toggle at each wakeup, not allowed with MODE = 1
The strobe pin will control the OFF/ON state of the MC33696. The various available sequences are described in the following subsections.
11.3.4.1 BANKA = X, BANKB = 0
State A Strobe Pin OFF State A OFF
If strobe pin is 1, configuration is defined by Bank A, BANKS = 1 If strobe pin is 0, MC33696 configuration is OFF. If a message is received during State A, current state remains State A up to end of message.
MC33696 Data Sheet, Rev. 9 16 Freescale Semiconductor
Register Access through SPI
11.3.4.2 BANKA = 0, BANKB = 1
State B Strobe Pin OFF State B OFF
If strobe pin is 1, configuration is defined by Bank B, BANKS = 0. If strobe pin is 0, MC33696 configuration is OFF. If a message is received during State B, current state remains State B up to end of message.
11.3.4.3 BANKA = 1, BANK B = 1
State A Strobe Pin Banks Bit OFF State B OFF State A
If strobe pin is 1, configuration is defined by BANKS. BANKS is toggled at each falling edge of the strobe pin. If strobe pin is 0, MC33696 configuration is OFF. If a message is received during state A or state B, current state remains the same up to end of message. If a read or write access is done using SPI, the next sequence will begin with state A whatever was the active state before SPI access by MCU.
11.3.5 Strobe Oscillator Switch Control
The conditions to enter strobe oscillator switch control are: * Strobe pin connected to an external capacitor to define timing (see Section 14, "Receiver On/Off Control") * Strobe pin can also be connected to the MCU I/O port * SOE bit = 1 By simply writing BANKA and BANKB, the active banks will be defined.
BANKA X 0 1 BANKB 0 Bank A is active (TX or RX) 1 Bank B is active (TX or RX) 1 Bank A and Bank B are both active, configuration will toggle at each wakeup, not allowed with MODE = 1
MCU can override strobe oscillator control by controlling strobe pin level. If MCU I/O port is in high impedance, strobe oscillator will control the OFF/ON state of the MC33696. The various available sequences are described in the following subsections.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 17
Register Access through SPI
11.3.5.1 BANKA = X, BANKB = 0
State A OFF State A OFF State A
If strobe pin is 1, configuration is defined by Bank A, BANKS = 1. If strobe pin is 0, MC33696 configuration is OFF. If a message is received during State A, current state remains State A up to end of message.
11.3.5.2 BANKA = 0, BANKB = 1
State B OFF State B OFF State B
If strobe pin is 1, configuration is defined by Bank B, BANKS = 0. If strobe pin is 0, MC33696 configuration is OFF. If a message is received during State B, current state remains State B up to end of message.
11.3.5.3 BANKA = 1, BANK B = 1
State A Banks Bit State B OFF StateA StateB OFF
BANKS toggles at the end of each state A or state B. If strobe is forced to 1, configuration is frozen according to BANKS value. If a read or write access is done using SPI, the next sequence will begin with state A in whatever was the active state before SPI access by MCU.
A Strobe Banks 1 Z B OFF A B OFF A B OFF A B
For all available sequences: * State A and State B are defined by Bank A and Bank B. * State A duration, TonA is defined by Bank A RON[3-0]. * State B duration, TonB is defined by Bank B RON[3-0]. * OFF duration, TonB is defined by Bank A ROFF[2-0]. * If strobe pin is 1, the state is ON and defined by BANKS at that time and remains this state up to the release of strobe and end of message if a message is being received. * If a message is being received during State A or B, current state remains State A or B up to end of message.
MC33696 Data Sheet, Rev. 9 18 Freescale Semiconductor
Communication Protocol
* * *
If strobe pin is 0 the state is OFF. If strobe pin is released from 0 while state is OFF, the initial OFF period is completed. Whenever is the change of duration of one state due to STROBE pin level or a message being received, this has no influence on the timing of the following states (A, B, or OFF).
11.4 Standby: LVD Mode
The SPI is deselected. Nothing is sent and all incoming data are ignored until CONFB and SEB go low to switch back to configuration mode.
12
Communication Protocol
12.1 Manchester Coding Description
The MC33696 data manager is able to decode Manchester coded messages. For other codings, the data manager should be disabled (DME=0) for RAW data to be available on MOSI. Manchester coding is defined as follows: data is sent during the first half-bit; and the complement of the data is sent during the second half-bit.
0 1 0 0 1 1 0 ORIGINAL DATA MANCHESTER CODED DATA
Figure 7. Example of Manchester Coding
The signal average value is constant. This allows clock recovery from the data stream itself. To achieve correct clock recovery, Manchester coded data must have a duty cycle between 47% and 53%.
12.2 Preamble, Identifier, Header, and Message
The following description applies if the data manager is enabled (DME = 1). A complete telegram includes the following sequences: a preamble, an identifier (ID), the preamble again, a header, the message, and an end-of-message (EOM). These bit sequences are described below. * Preamble: A preamble is required before the ID and before the header. It enables: -- In the case of OOK modulation, the AGC to settle, and the data slicer reference voltage to settle if DSREF = 1 -- In the case of FSK modulation, the data slicer reference voltage to settle -- Clock recovery The preamble content must be defined carefully, to ensure that it will not be decoded as the ID or the header. Figure 8 defines the preamble in OOK and FSK modulation.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 19
Communication Protocol
*
*
ID: The ID allows selection of the correct device in an RF transmission, as the content has been loaded previously in the ID register. Its length is variable, defined by the IDL[1:0] bits. The complement of the ID is also recognized as the identifier. Header: The header specifies the beginning of the message, as it is compared with the HEADER register. Its length is variable, defined by the HDL[1:0] bits. The complement of the header is also recognized as the header, in this case, output data are complemented. The ID and the header are sent at the same data rate as data. Message: Data must follow the header, with no delay. EOM: The message is completed with an end-of-message, consisting of two consecutive NRZ ones or zeroes (i.e., a Manchester code violation). Even in the case of FSK modulation, data must conclude with an EOM, and not simply by stopping the RF telegram.
* * *
Figure 9 shows a complete message comprising a 6-bit ID and a 4-bit header, followed by two data bits.
OOK MODULATION (DSREF = 0) AGC Settling Time Clock Recovery ID 1 NRZ > 200 s (1) 1 Manchester `0' Symbol at Data Rate
OOK MODULATION (DSREF = 1) AGC Settling Time Data Slicer Reference Settling Time Clock Recovery ID 1 NRZ > 200 s (1) At Least 3 Manchester 0 Symbols at Data Rate (2 and 3) Clock Recovery ID At Least 3 Manchester 0 Symbols at Data Rate (2 and 3) 1 Manchester 0 Symbol at Data Rate (3) 1 Manchester 0 Symbol at Data Rate (3)
FSK MODULATION (DSREF = 1) Data Slicer Reference Settling Time
NOTES: 1. The AGC settling time pulse can be split over different pulses as long as the overall duration is at least 200 s. 2. Table 15 defines the minimum number of Manchester symbols required for the data slicer operation versus the data and average filters cut-off frequencies. 3. The Manchester 0 symbol can be replaced by a 1.
Figure 8. Preamble Definition
1
1
0
01
1
01
1
01
0
Preamble
ID
Preamble
Header
Data
EOM
Figure 9. Complete Message Example
MC33696 Data Sheet, Rev. 9 20 Freescale Semiconductor
Communication Protocol
NOTE It is possible to build a tone to form the detection sequence by programming the ID register with a full sequence of ones or zeroes. In this case, the header (or its complement) must not be found in this tone (i.e., it must not be a full sequence of ones or zeroes).
12.3 Message Protocol
When the strobe oscillator is enabled (SOE = 1), the receiver is continuously on/off cycling. The ID must be recognized for the receiver to stay on. Consequently, the transmitted ID burst must be long enough to include two consecutive receiver On cycles. When the strobe oscillator is not enabled (SOE = 0), these timing constraints must be respected by the external control applied to pin STROBE.
P+ID
=
Preamble
ID
P+Header
=
Preamble
Header
RF Signal
P+ID
P+ID
P+ID
P+ID
P+ID
P+ID
P+Header
Data
EOM
Receiver Status
On On Time
Off Off Time ID Detected
On
Off
SPI Output
Data
Figure 10. Complete Telegram with ID Detection
RF Signal
Tone
Header
Data
EOM
Receiver Status
On On Time
Off Off Time ID Detected
On
Off
SPI Output
Data
Figure 11. Complete Telegram with Tone Detection
12.4 Receiver Startup Delay
As shown in Figure 12, a settling time is required when entering the on state.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 21
Data Manager
Receiver Status
Off
On
Off Settling Time
On
RF Signal
ID
ID
ID
ID
ID
ID
ID
ID
ID Detected
Figure 12. Receiver Usable Window
13
Data Manager
In receive mode, Manchester coded data can be processed internally by the data manager. After decoding, the data are output on the digital interface, in SPI format. This minimizes the load on the MCU. The data manager, when enabled (DME = 1), has five purposes: * ID detection: The received identifier is compared with the identifier stored in the ID register. * Header recognition: The received header is compared with the one stored in the HEADER register. * Clock recovery: The clock is recovered during reception of the preamble and is computed from the shortest received pulse. During the reception of the telegram, the recovered clock is constantly updated to the data rate of the incoming signal. * Output data and recovered clock on digital interface: See Section 15.2, "Receive Mode." * End-of-message detection: An EOM consists of two consecutive NRZ ones or zeroes. Table 8 details some MC33696 features versus DME values.
Table 8. the MC33696 Features versus DME
DME 0 1 Digital Interface Use SPI deselected SPI master when CONFB = 1 Data Format Bit stream No clock Data bytes Recovered clock Output MOSI -- MOSI SCLK
14
Receiver On/Off Control
In receive mode, on/off sequencing can be controlled internally, or managed externally by the MCU through the input pin STROBE. If the internal timer is selected (SOE = 1), * Off time is clocked by the strobe oscillator, * On time is clocked by the crystal oscillator, enabling accurate control of the on time and, therefore, the current consumption of the whole system.
MC33696 Data Sheet, Rev. 9 22 Freescale Semiconductor
Communication in Transmit and Receive Mode
Each time is defined with the associated value found in the RXONOFF register. * On time = RON[3:0] x 512 x Tdigclk (see Table 20; begins after the crystal oscillator has started), * Off time = receiver OFF time = N x TStrobe + MIN (TStrobe / 2, receiver On time), with N decoded from ROFF[2:0] (see Table 21). The strobe oscillator is a relaxation oscillator in which an external capacitor C3 is charged by an internal current source (see Figure 47). When the threshold is reached, C3 is discharged and the cycle restarts. The strobe frequency is FStrobe = 1/TStrobe with TStrobe = 106 x C3. In receive mode, setting the STROBE pin to VCCIO at any time forces the circuit on. As VCCIO is above the oscillator threshold voltage, the condition on which the STROBE pin is set to VCCIO is detected internally, and the oscillator pulldown circuitry is disabled. This limits the current consumption. After a strobe forced at "1", the external driver should pass via a "0" state to discharge the capacitor before going to high impedance state (otherwise, the ON time would last a long time after the driver release). When the strobe oscillator is running (i.e., during an off time), forcing the STROBE pin to VGND stops the strobe clock and, therefore, maintains the circuit off. Figure 13 shows the associated timings.
STROBE STROBE Clock Off Counter Digital Clock On Counter RON Receiver Status Off Cycling Period Crystal Oscillator Startup On 0 RON Off 0 RON On 0 ROFF-1 ROFF Threshold STROBE SET TO VCCIO tStrobe 0
Figure 13. Receiver On/Off Sequence
15
Communication in Transmit and Receive Mode
15.1 Transmit Mode
The SPI is deselected. The MC33696 receives the telegram to transmit on the MOSI line (see Figure 14).
SEB MOSI (Input)
Data
Figure 14. Transfer in Transmit Mode
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 23
Received Signal Strength Indicator (RSSI)
In OOK modulation (MODU=0), modulation is performed by switching on and off the RF output stage. MOSI = 0: output stage off MOSI = 1: output stage on In FSK modulation (MODU = 1), modulation is performed by switching the RF carrier between two values. MOSI = 0: fcarrier0 corresponding to a logical 0 MOSI = 1: fcarrier1 corresponding to a logical 1 See the FRM bit description (Figure 20) and Section 17.3, "Frequency Registers," for more details about setting carrier frequencies.
15.2 Receive Mode
The MC33696 is master and drives the digital interface in one of two ways, depending on the selection of the data manager. 1. DME = 1: The data manager is enabled. The SPI is master. The MC33696 sends the recovered clock on SCLK and the received data on the MOSI line. Data are valid on falling edges of SCLK. If an entire number of bytes is received, the data manager may add an extra byte. The content of this extra byte is random. If the data received do not fill an entire number of bytes, the data manager will fill the last byte randomly. Figure 15 shows a typical transfer.
SEB SCLK (Output) Recovered Clock Updated to Incoming Signal Data Rate MOSI (Output) D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
Figure 15. Typical Transfer in Receive Mode with Data Manager
2. DME = 0: The data manager is disabled. The SPI is deselected. Raw data are sent directly on the MOSI line, while SCLK remains at the low level.
16
Received Signal Strength Indicator (RSSI)
16.1 Module Description
In receive mode, a received signal strength indicator can be activated by setting bit RSSIE. The input signal is measured at two different points in the receiver chain by two different means, as follows. * At the IF filter output, a progressive compression logarithmic amplifier measures the input signal, ranging from the sensitivity level up to -50 dBm.
MC33696 Data Sheet, Rev. 9 24 Freescale Semiconductor
Received Signal Strength Indicator (RSSI)
*
At the LNA output, the LNA AGC control voltage is used to monitor input signals in the range -50 dBm to -20 dBm.
Therefore, the logarithmic amplifier provides information relative to the in-band signal, whereas the LNA AGC voltage senses the input signal over a wider band. The RSSI information given by the logarithmic amplifier is available in: * * Analog form on pin RSSIOUT Digital form in the four least significant bits of the status register RSSI
The information from the LNA AGC is available in digital form in the four most significant bits of status register RSSI. The whole content of status register RSSI provides 2 x 4 bits of RSSI information about the incoming signal (see Section 17.6, "RSSI Register"). Figure 16 shows a simplified block diagram of the RSSI function. The quasi peak detector (D1, R1, C1) has a charge time of about 20 s to avoid sensitivity to spikes. R2 controls the decay time constant of about 5 ms to allow efficient smoothing of the OOK modulated signal at low data rates. This time constant is useful in continuous mode when S2 is permanently closed. To allow high-speed RSSI updating in peak pulse measurement, a discharge circuit (S1) is required to reset the measured voltage and to allow new peak detection.
RSSI Register LNA AGC Out IF Filter Output ADC MSB LSB
S2
D1
R1
RSSIOUT C1 R2 S1 C2
Figure 16. RSSI Simplified Block Diagram
S2 is used to sample the RSSI voltage to allow peak pulse measurement (S2 used as sample and hold), or to allow continuous transparent measurement (S2 continuously closed). The 4-bit analog-to-digital convertor (ADC) is based on a flash architecture. The conversion time is 16 x Tdiglck. As a single convertor is used for the two analog signals, the RSSI register content is updated on a 32 x Tdigclk timebase. If RSSIE is reset, the whole RSSI module is switched off, reducing the current consumption. The output buffer connected to RSSIOUT is set to high impedance.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 25
Received Signal Strength Indicator (RSSI)
16.2 Operation
Two modes of operation are available: sample mode and continuous mode.
16.2.1 Sample Mode
Sample mode allows the peak power of a specific pulse in an incoming frame to be measured. The quasi peak detector is reset by closing S1. After 7 x Tdigclk, S1 is released. S2 is closed when RSSIC is set high. On the falling edge of RSSIC, S2 is opened. The voltage on RSSIOUT is sampled and held. The last RSSI conversion results are stored in the RSSI register and no further conversion is done. The RSSI register is updated every 32 x Tdigclk. Therefore, the minimum duration of the high pulse on RSSIC is 32 x Tdigclk.
RSSIC 7 x tdigclk S1 S2 RSSI Register Closed Open Closed
Open Frozen
Closed Updated
Open Frozen
RSSIOUT
Sampled and Hold RSSI Voltage
Peak Detector Reset CONFB MOSI
Sampling
CMD
MISO
RSSI Value
Figure 17. RSSI Operation in Sample Mode
MC33696 Data Sheet, Rev. 9 26 Freescale Semiconductor
Configuration, Command, and Status Registers
16.2.2 Continuous Mode
Continuous mode is used to make a peak measurement on an incoming frame, without having to select a specific pulse to be measured. The quasi peak detector is reset by closing S1. After 7 x Tdigclk, S1 is opened. S2 is closed when RSSIC is set high. As long as RSSIC is kept high, S2 is closed, and RSSIOUT follows the peak value with a decay time constant of 5 ms. The ADC runs continuously, and continually updates the RSSI register. Thus, reading this register gives the most recent conversion value, prior to the register being read. The minimum duration of the high pulse on CONFB is 32 x Tdigclk.
RSSIC 5 x tdigclk S1 S2 RSSI Register Closed Open Frozen Updated Frozen Open Closed Updated Frozen
RSSIOUT
Peak Detector Test CONFB MOSI CMD
CMD
MISO
RSSI
RSSI
Figure 18. RSSI Operation in Continuous Mode
17
Configuration, Command, and Status Registers
This section discusses the internal registers, which are composed of two classes of bits. * Configuration and command bits allow the MC33696 to operate in a suitable configuration. * Status bits report the current state of the system. All registers can be accessed by the SPI; these registers are described below. At power-on, the POR resets all registers to a known value (in the shaded rows in the following tables). This defines the MC33696's default configuration. After POR, CONFB forces a low level. Therefore, an external pullup resistor is required to avoid entering configuration mode.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 27
Configuration, Command, and Status Registers
17.1 Configuration Registers
Figure 19 describes configuration register 1, CONFIG1.
Bit 7 Bit Name Reset Value LOF1 1 Bit 6 LOF0 0 Bit 5 CF1 0 Bit 4 CF0 1 Bit 3 RESET 0 Bit 2 SL 0 Bit 1 LVDE 0 Bit 0 CLKE 1 Addr $00
Figure 19. CONFIG1 Register Table 9. LOF[1:0] and CF[1:0] Setting Versus Carrier Frequency
Carrier Frequency 304 MHz 315 MHz 426 MHz 434 MHz 868 MHz 915 MHz LOF1 0 1 0 0 0 1 LOF0 0 0 1 1 1 1 CF1 0 0 0 0 1 1 CF0 0 0 1 1 1 1
RESET is a global reset. The bit is cleared internally, after use. 0 = no action 1 = reset all registers and counters SL (Switch Level) selects the active level of the SWITCH output pin.
Table 10. Active Level of SWITCH Output Pin
SL 0 Transceiver Function Receiving Transmitting 1 Transmitting Receiving Level on SWITCH Low High Low High
LVDE (Low Voltage Detection Enable) enables the low voltage detection function. 0 = disabled 1 = enabled NOTE This bit is cleared by POR. In the event of a complete loss of the supply voltage, LVD is disabled at power-up, but the information is not lost as the status bit LVDS is set by POR. CLKE (Clock Enable) controls the DATACLK output buffer. 0 = DATACLK remains low 1 = DATACLK outputs Fdataclk
MC33696 Data Sheet, Rev. 9 28 Freescale Semiconductor
Configuration, Command, and Status Registers
Figure 20 describes configuration register 2, CONFIG2.
Bit 7 Bit Name Reset Value DSREF 0 Bit 6 FRM 0 Bit 5 MODU 0 Bit 4 DR1 1 Bit 3 DR0 0 Bit 2 TRXE 0 Bit 1 DME 0 Bit 0 SOE 0 Addr $01
Figure 20. CONFIG2 Register
DSREF (Data Slicer Reference) selects the data slicer reference. 0 = Fixed reference (cannot be used in FSK) 1 = Adaptive reference (recommended for maximum sensitivity in OOK and FSK) In the case of FSK modulation (MODU = 1), DSREF must be set. FRM (Frequency Register Manager) enables either a user friendly access to one frequency register or a direct access to the two frequency registers. 0 = The carrier frequency and the FSK deviation are defined by the F register 1 = The local oscillator frequency and the two carrier frequencies are defined by two frequency registers, F and FT. MODU (Modulation) sets the data modulation type. 0 = On/Off Keying (OOK) modulation 1 = Frequency Shift Keying (FSK) modulation DR[1:0] (Data Rate) configure the receiver blocks operating in base band. * Low-pass data filter * Low-pass average filter generating the data slicer reference, if DSREF is set * Data manager
Table 11. Base Band Parameter Configuration
DR1 0 0 1 1 DR0 0 1 0 1 Data Filter Cut-off Frequency 6 kHz 12 kHz 24 kHz 48 kHz Average Filter Cut-off Frequency 0.5 kHz 1 kHz 2 kHz 4 kHz Data Manager Data Rate Range 2-2.8 kBd 4-5.6 kBd 8-10.6 kBd 16-22.4 kBd
If the data manager is disabled, the incoming signal data rate must be lower than or equal to the data manager maximum data rate. TRXE (Transceiver Enable) enables the whole transceiver. 0 = standby mode 1 = other modes can be activated DME (Data Manager Enable) enables the data manager. 0 = disabled 1 = enabled
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 29
Configuration, Command, and Status Registers
SOE (Strobe Oscillator Enable) enables the strobe oscillator. 0 = disabled 1 = enabled Figure 21 describes configuration register 3, CONFIG3.
Bit 7 Bit Name Reset Value AFF1 0 Bit 6 AFF0 0 Bit 5 OLS 1 Bit 4 LVDS 1 Bit 3 ILA1 0 Bit 2 ILA0 0 Bit 1 OLA1 0 Bit 0 OLA0 0 Addr $02
Figure 21. CONFIG3 Register
OLS (Out of Lock Status) indicates the current status of the PLL. 0 = The PLL is in lock-in range 1 = The PLL is out of lock-in range LVDS (Low Voltage Detection Status) indicates that a low voltage event has occurred when LVDE = 1. This bit is read-only and is cleared after a read access. 0 = No low voltage detected 1 = Low voltage detected ILA[1:0] (Input Level Attenuation) define the RF input level attenuation.
Table 12. RF Input Level Attenuation
ILA1 0 0 1 1 ILA0 0 1 0 1 RF Input Level Attenuation 0 dB 8 dB 16 dB 30 dB See Parameter Number 2.5 2.6 2.7 2.8
Values in Table 12 assume the LNA gain is not reduced by the AGC. OLA[1:0] (Output Level Attenuation) define the RF output level attenuation.
Table 13. RF Output Level Attenuation
OLA1 0 0 1 1 OLA0 0 1 0 1 RF Output Level Attenuation 0 dB 6 dB 12 dB 25 dB See Parameter Number 4.20 4.3 4.4 4.5
AFF[1:0] (Average Filter Frequency) define the average filter cut-off frequency if the AFFC bit is set.
MC33696 Data Sheet, Rev. 9 30 Freescale Semiconductor
Configuration, Command, and Status Registers
Table 14. Average Filter Cut-off Frequency
AFF1 0 0 1 1 AFF0 0 1 0 1 Average Filter Cut-off Frequency 0.5 kHz 1 kHz 2 kHz 4 kHz
If AFFC is reset, the average filter frequency is directly defined by bits DR[1:0], as shown in Table 11. If AFFC is set, AFF[1:0] allow the overall receiver sensitivity to be improved by reducing the average filter cut-off frequency. The typical preamble duration of three Manchester zeroes or ones at the data rate must then be increased, as shown in Table 15.
Table 15. Minimum Number of Manchester Symbols in Preamble versus DR[1:0] and AFF[1:0]
DR[1:0] 00 00 01 AFF[1:0] 10 11 3 -- -- -- 01 6 3 -- -- 10 12 6 3 -- 11 24 12 6 3
17.2 Command Register
Figure 22 describes the Command register, COMMAND.
Bit 7 Bit Name Reset Value AFFC 0 Bit 6 IFLA 0 Bit 5 MODE 0 Bit 4 RSSIE 0 Bit 3 EDD 1 Bit 2 RAGC 0 Bit 1 FAGC 0 Bit 0 -- 1 Addr $03
Figure 22. COMMAND Register
AFFC (Average Filter Frequency Control) enables direct control of the average filter cut-off frequency. 0 = Average filter cut-off frequency is defined by DR[1:0] 1 = Average filter cut-off frequency is defined by AFF[1:0] IFLA (IF Level Attenuation) controls the maximum gain of the IF amplifier in OOK modulation. 0 = No effect 1 = Decreases by 20 dB (typical) the maximum gain of the IF amplifier, in OOK modulation only The reduction in gain can be observed if the IF amplifier AGC system is disabled (by setting RAGC = 1). MODE selects the mode.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 31
Configuration, Command, and Status Registers
0 = Receive mode 1 = Transmit mode RSSIE (RSSI Enable) enables the RSSI function. 0 = Disabled 1 = Enabled EDD (Envelop Detector Decay) controls the envelop detector decay. 0 = Slow decay for minimum ripple 1 = Fast decay RAGC (Reset Automatic Gain Control) resets both receiver internal AGCs. 0 = No action 1 = Sets the gain to its maximum value A first SPI access allows RAGC to be set; a second SPI access is required to reset it. FAGC (Freeze Automatic Gain Control) freezes both receiver AGC levels. 0 = No action 1 = Holds the gain at its current value
17.3 Frequency Registers
Figure 23 and Figure 24 define the Frequency registers, F and FT.
Bit 15 Bit Name Reset Value FSK3 0 Bit 7 Bit Name Reset Value F7 0 Bit 14 FSK2 1 Bit 6 F6 0 Bit 13 FSK1 0 Bit 5 F5 0 Bit 12 FSK0 0 Bit 4 F4 0 Bit 11 F11 1 Bit 3 F3 0 Bit 10 F10 0 Bit 2 F2 0 Bit 9 F9 0 Bit 1 F1 0 Bit 8 F8 0 Bit 0 F0 0 $05 Addr $04
Figure 23. F Register
MC33696 Data Sheet, Rev. 9 32 Freescale Semiconductor
Configuration, Command, and Status Registers
Bit 23 Bit Name Reset Value FTA11 0 Bit 15 Bit Name Reset Value FTA3 0 Bit 7 Bit Name Reset Value FTB7 0
Bit 22 FTA10 1 Bit 14 FTA2 0 Bit 6 FTB6 0
Bit 21 FTA9 1 Bit 13 FTA1 0 Bit 5 FTB5 0
Bit 20 FTA8 1 Bit 12 FTA0 0 Bit 4 FTB4 0
Bit 19 FTA7 0 Bit 11 FTB11 0 Bit 3 FTB3 0
Bit 18 FTA6 0 Bit 10 FTB10 1 Bit 2 FTB2 0
Bit 17 FTA5 0 Bit 9 FTB9 1 Bit 1 FTB1 0
Bit 16 FTA4 0 Bit 8 FTB8 1 Bit 0 FTB0 1
Addr $06
$07
$08
Figure 24. FT Register
How these registers are used is determined by the FRM bit, which is described below. FRM = 0 (User Friendly Access) Whatever type of modulation is used (OOK or FSK), bits F[11:0] define the carrier frequency Fcarrier. The local oscillator frequency FLO is then set automatically to Fcarrier + FIF (with FIF = intermediate frequency). In addition, * in the case of OOK modulation (MODU = 0): -- FSK[3:0], FTA[11:0], and FTB[11:0] are not used. * in the case of FSK modulation (MODU = 1): -- FSK[3:0] sets the frequency deviation Df as defined in Table 16.
Table 16. Frequency Deviation Definition
CF[1:0] 00, 01 11 Frequency Deviation f Fref x(FSK[3:0]+1)/ 2048 Frefx(FSK[3:0]+1)/ 1024
Table 17 gives a numerical example in the 434 MHz band (CF[1:0] = 01).
Table 17. Frequency Numerical Example (434 MHz Band)
FSK[3:0] 0000 0001 0010 ... 1111 Frequency Deviation f 12 kHz 24 kHz 36 kHz ... 192 kHz
Then, two frequencies are calculated internally, as follows. -- Fcarrier0 = F[11:0] - f to transmit a logical 0 -- Fcarrier1 = F[11:0] + f to transmit a logical 1 FTA[11:0] and FTB[11:0] are not used
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 33
Configuration, Command, and Status Registers
FRM = 1 (Direct Access) Whatever type of modulation is used (OOK or FSK), F[11:0] defines the receiver local oscillator frequency FLO, and, * if OOK modulation is used (MODU = 0): -- FTA[11:0] define the carrier frequency Fcarrier -- FTB[11:0] are not used * if FSK modulation is used (MODU = 1): -- FTA[11:0] define the carrier frequency Fcarrier0 to transmit a logical 0 -- FTB[11:0] define the carrier frequency Fcarrier1 to transmit a logical 1 Table 18 defines the value to be binary coded in the frequency registers F[11;0], FTA/B[11:0], versus the desired frequency value F (in Hz).
Table 18. Frequency Register Value versus Frequency Value F
CF[1:0] 00, 01 11 Frequency Register Value (2 x F/Fref-35) x 2048 (F/Fref-35) x 2048
Conversely, Table 19 gives the desired frequency F and the frequency resolution versus the value of the frequency registers F[11;0].
Table 19. Frequency Value F versus Frequency Register Value
CF[1:0] 00, 01 11 Frequency (Hz) (35 + F[11;0]/2048)xFref/2 (35 + F[11;0]/2048)xFref Frequency Resolution (Hz) Fref/4096 Fref/2048
17.4 Receiver On/Off Duration Register
Figure 25 describes the receiver on/off duration register, RXONOFF.
Bit 7 Bit Name Reset Value -- 0 Bit 6 RON3 1 Bit 5 RON2 1 Bit 4 RON1 1 Bit 3 RON0 1 Bit 2 ROFF2 1 Bit 1 ROFF1 1 Bit 0 ROFF0 1 Addr $09
Figure 25. RXONOFF Register
RON[3:0] (Receiver On) define the receiver on time (after crystal oscillator startup) as described in Section 14, "Receiver On/Off Control."
Table 20. Receiver On Time Definition
RON[3:0] 0000 0001 0010 ... Receiver On Time: N x 512 x Tdigclk Forbidden value 1 2 ...
MC33696 Data Sheet, Rev. 9 34 Freescale Semiconductor
Configuration, Command, and Status Registers
Table 20. Receiver On Time Definition
RON[3:0] 1111 Receiver On Time: N x 512 x Tdigclk 15
ROFF[2:0] (Receiver Off) define the receiver off time as described in Section 14, "Receiver On/Off Control."
Table 21. Receiver Off Time Definition
ROFF[2:0] 000 001 010 011 100 101 110 111 Receiver Off Time: N x TStrobe 1 2 4 8 12 16 32 63
17.5 ID and Header Registers
Figure 26 defines the ID register, ID.
Bit 7 Bit Name Reset Value IDL1 1 Bit 6 IDL0 1 Bit 5 ID5 0 Bit 4 ID4 0 Bit 3 ID3 0 Bit 2 ID2 0 Bit 1 ID1 0 Bit 0 ID0 0 Addr $0A
Figure 26. ID Register
IDL[1:0] (Identifier Length) sets the length of the identifier, as shown on Table 22.
Table 22. ID Length Selection
IDL1 0 0 1 1 IDL0 0 1 0 1 ID Length 2 bits 4 bits 5 bits 6 bits
ID[5:0] (Identifier) sets the identifier. The ID is Manchester coded. Its LSB corresponds to the register's LSB, whatever the specified length. Figure 27 defines the Header register, HEADER.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 35
Controller
Bit 7 Bit Name Reset Value HDL1 1
Bit 6 HDL0 0
Bit 5 HD5 0
Bit 4 HD4 0
Bit 3 HD3 0
Bit 2 HD2 0
Bit 1 HD1 0
Bit 0 HD0 0
Addr $0B
Figure 27. HEADER Register
HDL[1:0] (Header Length) sets the length of the header, as shown on Table 23.
Table 23. Header Length Selection
HDL1 0 0 1 1 HDL0 0 1 0 1 HD Length 1 bits 2 bits 4 bits 6 bits
HD[5:0] (Header) sets the header. The header is Manchester coded. Its LSB corresponds to the register's LSB, whatever the specified length.
17.6 RSSI Register
Figure 28 describes the RSSI Result register, RSSI.
Bit 7 Bit Name Reset Value RSSI7 0 Bit 6 RSSI6 0 Bit 5 RSSI5 0 Bit 4 RSSI4 0 Bit 3 RSSI3 0 Bit 2 RSSI2 0 Bit 1 RSSI1 0 Bit 0 RSSI0 0 Addr $0C
Figure 28. RSSI Register
Bits RSSI[7:4] contain the result of the analog-to-digital conversion of the signal measured at the LNA output. Bits RSSI[3:0] contain the result of the analog-to-digital conversion of the signal measured at the IF filter output.
18
Controller
This section describes how the MC33696 controller executes sequences of operations, relative to the selected mode. The controller is a finite state machine, clocked at Tdigclk. An overview is presented in Figure 29 (note that some branches refer to other diagrams that provide more detailed information). There are four different modes: configuration, transmit, receive, and standby/LVD. Each mode is exclusive and can be entered in different ways, as follows. * External signal: CONFB for configuration mode, * External signal and configuration bits: CONFB, TRXE, and/or MODE for all other modes,
MC33696 Data Sheet, Rev. 9 36 Freescale Semiconductor
Controller
*
External signal and internal conditions: see Figure 33 and Figure 35 for information on how to enter standby/LVD mode.
After a POR, the circuit is in state 60 (see Figure 29) and configuration registers' content is set to the reset value. At any time, a low level applied to CONFB forces the finite state machine into state 1, whatever the current state. This is not always shown in state diagrams, but must always be considered.
State 30 Active Bank Change (A to B or B to A) SPI Deselected SPI Slave SPI Master
CONFB = 0
CONFB = 1, TRXE = 1, and MODE = 1 Configuration Mode Configuration Mode
Standby/LVD Mode State 60 CONFB = 1, TRXE = 0, and STROBE = 0
State 1 CONFB = 1, TRXE = 1, and STROBE = 0 ...and DME = 1
Power-on Reset ...and DME = 0 ...and SOE = 1 ...and SOE = 0
Receive Mode
...and SOE = 1
...and SOE = 0
See Figure 32
See Figure 33
See Figure 34
See Figure 35
Figure 29. State Machine Overview
18.1 Configuration Mode
The configuration mode is selected by the microcontroller unit (MCU) to write to the internal registers (to configure the system) or to read them. In this mode, the SPI is a slave. The analog parts (receiver and transmitter) remain in the state (on, off) they were in prior to entering configuration mode, until a new configuration changes them. In configuration mode, data can be neither sent nor received. As long as a low level is applied to CONFB, the circuit stays in State 1, the only state in this mode. Figure 30 and Figure 31 describe the two valid sequences for enabling a correct transition from Standby/LVD mode to configuration mode.
STROBE CONFB SPI Startup Time SEB
Figure 30. First Valid Sequence from Standby/LVD Mode to Configuration Mode
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 37
Controller
STROBE CONFB SPI Startup Time
10 s (Maximum) SEB
Figure 31. Second Valid Sequence from Standby/LVD Mode to Configuration Mode
18.2 Transmit Mode
In transmit mode, the state diagram is reduced to only one state: state 30. The circuit is either waiting for a digital telegram to send, or is sending one. In this mode, the circuit can be considered as a simple RF physical interface. The information presented on MOSI is sent directly in RF (according to the selected modulation), with no internal processing. Data transmission is possible only if the PLL is within the lock-in range. Therefore, during transmission, if the PLL switches out of lock-in range, the RF output stage is switched off internally, thereby preventing data from being transmitted in an unwanted band.
18.3 Receive Mode
The receiver is either waiting for an RF telegram, or is receiving one. Four different processes are possible, as determined by the values of the DME and SOE bits. The transmitter part is maintained off. A state diagram describes the sequence of operations in each case. NOTE If the STROBE pin is tied to a high level before switching to receive mode, the receiver does not go through an off or standby state.
18.3.1 Data Manager Disabled and Strobe Oscillator Enabled
Raw received data are sent directly on the MOSI line. Figure 32 shows the state diagram.
SPI Deselected STROBE = 0 STROBE = 0 STROBE = 1 State 0 Off Off Counter = ROFF[2:0] or STROBE = 1
On Counter = RON[3:0] and STROBE 1
State 0b On Raw Data on MOSI
Figure 32. Receive Mode, DME = 0, SOIE = 1
MC33696 Data Sheet, Rev. 9 38 Freescale Semiconductor
Controller
State 0: The receiver is off, but the strobe oscillator and the off counter are running. Forcing the STROBE pin low maintains the system in this state. State 0b: The receiver is kept on by the STROBE pin or the on counter. Raw data are output on the MOSI line. For all states: At any time, a low level applied to CONFB forces the state machine to state 1.
18.3.2 Data Manager Disabled and Strobe Pin Control
Raw received data are sent directly on the MOSI line. Figure 33 shows the state diagram.
SPI Deselected STROBE = 0
STROBE = 1
State 5 Standby/LVD
STROBE = 1
STROBE = 0
State 5b On Raw Data on MOSI
Figure 33. Receive Mode, DME = 0, SOE = 0
State 5: The receiver is in standby/LVD mode. For further information, see Section 18.4, "Standby/LVD Mode." A high level applied to STROBE forces the circuit to state 5b. State 5b: The receiver is kept on by the STROBE pin. Raw data are output on the MOSI line. For all states: At any time, a low level applied to CONFB forces the state machine to state 1.
18.3.3 Data Manager Enabled and Strobe Oscillator Enabled
Figure 34 shows the state diagram when the data manager and the strobe oscillator are enabled. in this configuration, the receiver is controlled internally by the strobe oscillator. However, external control via the STROBE pin is still possible, and overrides the strobe oscillator command. State 10: The receiver is off, but the strobe oscillator and the off counter are running. Forcing STROBE pin to the low level maintains the system in this state. State 11: The receiver is waiting for a valid ID. If an ID, or its complement, is detected, the state machine advances to state 12; otherwise, the circuit goes back to state 10 at the end of the RON time, if STROBE1. State 12: An ID or its complement has been detected. The data manager is now waiting for a header or its complement. If neither a header, nor its complement, has been received before a time-out of 256 bits at data rate, the system returns to state 10.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 39
Controller
State 13: A header, or its complement, has been received. Data and clock signals are output on the SPI port until EOM indicates the end of the data sequence. If the complement of the header has been received, output data are complemented also. When an EOM occurs before the current byte is fully shifted out, dummy bits are inserted until the number of shifted bits is a multiple of 8. For all states: At any time, a low level applied to STROBE forces the circuit to state 10, and a low level applied on CONFB forces the state machine to state 1.
SPI Master STROBE = 0 STROBE = 0 State 10 Off STROBE = 1
Off Counter = ROFF[2:0] or STROBE = 1
On Counter = RON[3:0] and STROBE 1
State 11 On Waiting For a Valid ID
ID Detected
Time Out
State 12 On Waiting for a Valid Header
EOM Received and STROBE = 1
Header Received
State 13 On Output Data and Clock Waiting for End of Message EOM Received and STROBE 1
Figure 34. Receive Mode, DME = 1, SOE = 1
MC33696 Data Sheet, Rev. 9 40 Freescale Semiconductor
Controller
18.3.4 Data Manager Enabled and Strobe Pin Control
Figure 35 shows the state diagram when the data manager is enabled and the strobe oscillator is disabled. In this configuration, the receiver is controlled only externally by the MCU.
SPI Master STROBE = 0 SPI Deselected State 20 Standby/LVD
STROBE = 1
STROBE = 1
STROBE = 0
State 21 On Waiting For a Valid ID
ID Detected
STROBE = 0
State 22 On Waiting for a Valid Header
EOM Received and STROBE = 1
Header Received
State 23 On Output Data and Clock Waiting for End of Message EOM Received and STROBE = 0
Figure 35. Receive Mode, DME = 1, SOE = 0
State 20: The receiver is in standby/LVD mode. For further information, see Section 18.4, "Standby/LVD Mode." A high level applied to STROBE forces the circuit to state 21. State 21: The circuit is waiting for a valid ID. If an ID, or its complement, is detected, the state machine advances to state 22; if not, the state machine will remain in state 21, as long as STROBE is high. State 22: If a header, or its complement, is detected, the state machine advances to state 23. If not, the state machine will remain in state 22, as long as STROBE is high. State 23: A header or its complement has been received; data and clock signals are output on the SPI port until an EOM indicates the end of the data sequence. If the complement of the header has been received,
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 41
Controller
output data are complemented also. When an EOM occurs before the current byte is fully shifted out, dummy bits are inserted until the number of shifted bits is a multiple of 8. For all states: At any time, a low level applied to STROBE puts the circuit into state 20, and a low level applied to CONFB forces the state machine to state 1.
18.4 Standby/LVD Mode
Standby/LVD mode allows minimum current consumption to be achieved. Depending upon the value of the LVDE bit, the circuit is in standby mode (state 60) or LVD mode (state 5 and 20). LVDE = 0: The transceiver is in standby; consumption is reduced to leakage current (current state after POR). LVDE = 1: The LVD function is enabled; consumption is in the range of tens of microamperes. The only way to exit this mode is to go back to configuration mode by applying a low level to CONFB.
18.5 Transition Time
Table 24 details the different times that must be considered for a given transition in the state machine, once the logic conditions for that transition are met.
Table 24. Transition Time Definition
Transition State x -> y Standby to SPI running, state 60 -> 1 Standby to receiver running, states 5 -> 5b, 20 -> 21 Off to receiver running, states 0 -> 0b, 10 -> 11 Configuration to receiver running, states 1 -> (0b, 5b, 11, 21) Configuration to transmitter mode, state 1 -> 30 Crystal Oscillator Startup Time, Parameter 5.10 Receiver Receiver Preamble On-to-Off Time, Parameter 1.12 Time1
PLL Timing
Lock time parameter 5.9 Lock time parameter 5.9 0 or lock time parameter 5.1 or lock time parameter 5.9 2 0 or lock time parameter 5.1 or lock time parameter 5.9 2

Receiver running to configuration mode, state (0b, 5b, 11, 12, 13, 21, 22, 23) -> 1, Transmitter mode to configuration mode, state 30 -> 1 Receiver running to standby mode, state 5b -> 5, (21, 22, 23) -> 20 Receiver running to off mode, state 0b -> 0, (11, 12, 13) -> 10

NOTES: 1 See Section 12.2, "Preamble, Identifier, Header, and Message." 2 Depending on the PLL status before entering configuration mode. For example, the transition time from standby to receiver running (FSK modulation, 19.2 kBd, AFFC = 0, data manager enabled) is: 0.6 ms + 50 s + (3 + 1)/19.2k = 970 s.
MC33696 Data Sheet, Rev. 9 42 Freescale Semiconductor
Electrical Characteristics
19
Electrical Characteristics
19.1 General Parameters
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Parameter 1.2 Supply current in receive mode 1.3 Test Conditions Comments Receiver on Strobe oscillator only Limits Unit Min -- -- -- -- -- -- -- -- 2.4 -- -- 1.4 2.4 Typ 10.3 24 13.5 6.1 260 800 35 100 2.6 VCC-0.1 0.7 x VCCDIG 1.6 -- Max 13 50 17.5 8 700 1200 50 -- 2.8 -- -- 1.8 -- mA A mA mA nA nA A s V V V V V
1.4 Supply current in transmit mode Continuous wave (CW) OLA[1:0}=00 1.5 No power output
1.6 Supply current in standby mode -40C TA 25C 1.8 1.9 Supply current in LVD mode 1.12 Receiver on-to-off time 1.13 VCC2 voltage regulator output 1.14 1.15 VCCDIG2 voltage regulator output 1.16 1.19 Voltage on VCC (Preregulator output) TA = 85C LVDE = 1 Supply current reduced to 10% 2.7 V < VCC 2.1 V VCC 2.7 V Circuit in standby mode (VCCDIG = 3 V) Circuit in all other modes Receive mode with VCCIN=5V
19.2 Receiver: RF Parameters
RF parameters assume a matching network between test equipment and the D.U.T, and apply to all bands unless otherwise specified.
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Limits Parameter Test Conditions, Comments Max (FCE, FJE) -99 -98 Max (FCAE, FJAE) -97 -96 Unit
Min -- --
Typ -104 -103.5
2.2 OOK sensitivity at 315 MHz DME = 1, DSREF = 1, DR = 4.8 kbps, PER = 0.1 2.40 OOK sensitivity at 434 MHz DME = 1, DSREF = 1, DR = 4.8 kbps, PER = 0.1
dBm dBm
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 43
Electrical Characteristics Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Limits Parameter Test Conditions, Comments Max (FCE, FJE) -98 -98 -102 Max (FCAE, FJAE) -96 -96 -100 Unit
Min -- -- --
Typ -103 -103 -106.5
2.41 OOK sensitivity at 868 MHz DME = 1, DSREF = 1, DR = 4.8 kbps, PER = 0.1 2.42 OOK sensitivity at 916 MHz DME = 1, DSREF = 1, DR = 4.8 kbps, PER = 0.1 2.24 FSK sensitivity at 315 MHz DME = 1, DSREF = 1, DR = 4.8 kbps, DFcarrier = 64 kHz, PER = 0.1 DME = 1, DSREF = 1, DR = 4.8 kbps, DFcarrier = 64 kHz, PER = 0.1 DME = 1, DSREF = 1, DR = 4.8 kbps, DFcarrier = 64 kHz, PER = 0.1 DME = 1, DSREF = 1, DR = 4.8 kbps, DFcarrier = 64 kHz, PER = 0.1 DME = 0 ILA[1:0] = 00 ILA[1:0] = 01 ILA[1:0] = 10 ILA[1:0] = 11 Sensitivity reduced by 3 dB CW jammer at Fcarrier 50 kHz/OOK Sensitivity reduced by 3 dB CW jammer at Fcarrier 50 kHz/FSK Sensitivity reduced by 3dB CW jammer at Fcarrier 1 MHz Sensitivity reduced by 3dB CW jammer at Fcarrier 2 MHz Receive mode Transmit mode Receive and transmit modes
dBm dBm dBm
2.50 FSK sensitivity at 434 MHz
--
-105.5
-101
-99
dBm
2.51 FSK sensitivity at 868 MHz
--
-104.5
-100
-98
dBm
2.52 FSK sensitivity at 916 MHz
--
-105.4
-102
-100
dBm
2.35 Sensitivity improvement in RAW mode 2.5 Sensitivity reduction 2.6 2.7 2.8 2.9 In-band jammer desensitization 2.60 2.11 Out-of-band jammer desensitization 2.12 2.13 RFIN parallel resistance 2.14 RFIN parallel resistance 2.15 RFIN parallel capacitance
-- -- -- -- -- -- -- -- -- -- 1300 -- -25 -10
0.6 0 8 16 30 -4 -6 37 40 300 -- 1.2 -- --
-- -- -- -- -- -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- -- -- -- --
dB dB dB dB dB dBc dBc dBc dBc pF dBm dBm
2.17 Maximum detectable signal, Modulation depth: 99%, OOK level measured on a NRZ `1' 2.25 Maximum detectable signal, Fcarrier = 64kHz FSK
MC33696 Data Sheet, Rev. 9 44 Freescale Semiconductor
Electrical Characteristics Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Limits Parameter Test Conditions, Comments Max (FCE, FJE) -- -- Max (FCAE, FJAE) -- -- Unit
Min 20 15
Typ 36 20
2.18 Image frequency rejection 2.19
304-434 MHz 868-915 MHz
dB dB
OOK Sensitivity Variation vs Temperature (Ref : 3V, 25C, 4800bps) 1.4 1.2 Sensitivity Variation (dB) 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -40C 315 MHz 434 MHz 868 MHz 916 MHz
25C Temperature (C)
85C
Figure 36. OOK Sensitivity Variation Versus Temperature
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 45
Electrical Characteristics
OOK Sensitivity Variation vs Voltage (Ref : 3V, 25C, 4800bps) 0.2 0.1 Sensitivity Variation (dB) 0 -0.1 -0.2 -0.3 -0.4 -0.5 2.1 V 315 MHz 434 MHz 868 MHz 916 MHz
2.4 V
Voltage (V)
3V
3.6 V
Figure 37. OOK Sensitivity Variation Versus Voltage
FSK Sensitivity Variation vs Temperature (Ref : 3V, 25C, +/-64kHz, 4800 bps ) 1.4 1.2 1 Sensitivity Variation (dB) 0.8 0.6 0.4 0.2 0 315 MHz 434 MHz 868 MHz 916 MHz
-0.2 -0.4 -0.6 -40C
25C Temperature (C)
85C
Figure 38. FSK Sensitivity Variation Versus Temperature
MC33696 Data Sheet, Rev. 9 46 Freescale Semiconductor
Electrical Characteristics
FSK Sensitivity Variation vs Voltage (Ref : 3V, 25C, +/-64kHz, 4800bps ) 0.5 0.4 315 MHz Sensitivity Variaition (dB) 0.3 0.2 0.1 0 -0.1 -0.2 2.1 V 434 MHz 868 MHz 916 MHz
2.4 V
Voltage (V)
3V
3.6 V
Figure 39. FSK Sensitivity Variation Versus Voltage
Sensitivity Variation Versus Data Rate (Ref : 25C, 3V, 434MHz , OOK, 4800bps) 5 4 Sensitivity Variation (dB) 3 2 1 0 -1 -2 -3 2400
4800 Data Rate (bps)
9600
19200
Figure 40. OOK Sensitivity Variation Versus Data Rate
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 47
Electrical Characteristics
Sensitivity Variation vs Data Rate (Ref : 25C, 3V, 434MHz , FSK +/-64kHz, 4800bps) 5 4 Sensitivity Variation (dB) 3 2 1 0 -1 -2 -3 2400
4800 Data Rate (bps)
9600
19200
Figure 41. FSK Sensitivity Variation Versus Data Rate
Sensitivity Variation vs Frequency Deviation (Ref : 25C, 3V, 434MHz, FSK +/-64kHz, 4800bps) 6 5 Sensitivity Variation (dB) 4 3 2 1 0 -1 20 32 40 50 65 70 80 90 100 110 120 130 140 150 Frequency Deviation (kHz) 160 170
Figure 42. FSK Sensitivity Variation Versus Frequency Deviation
MC33696 Data Sheet, Rev. 9 48 Freescale Semiconductor
Electrical Characteristics
19.3 Receiver Parameters
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Parameter Test Conditions Comments Limits Unit Min Typ Max
Receiver: IF filter, IF Amplifier, FM-to-AM Converter and Envelope Detector 3.1 IF center frequency 3.2 IF bandwidth at -3dB 3.3 IF cut-off low frequency at -3 dB Refer to Section 10, "Frequency Planning". 3.4 IF cut-off high frequency at -3 dB 3.12 Recovery time from strong signal OOK modulation, 2.4 kbps, FAGC = 0, input signal from -50 dBm to -100 dBm -- -- -- 1.635 -- 1.5 380 -- -- 15 -- -- 1.387 -- -- MHz kHz MHz MHz ms
Receiver: Analog and Digital RSSI 3.51 Analog RSSI output signal for Input signal @-108 dBm 3.52 Analog RSSI output signal for Input signal @-100 dBm 3.53 Analog RSSI output signal for Input signal @-70 dBm 3.54 Analog RSSI output signal for Input signal @-28 dBm 3.55 Digital RSSI Registers for Input signal @-108 dBm 3.56 Digital RSSI Registers for Input signal @-100 dBm 3.57 Digital RSSI Registers for Input signal @-70 dBm 3.58 Digital RSSI Registers for Input signal @-28 dBm 3.59 Digital RSSI Registers for Input signal @-70 dBm 3.6 Digital RSSI Registers for Input signal @-50 dBm 3.61 Digital RSSI Registers for Input signal @-24 dBm RSSI [4:7] RSSI [0:3] Measured on RSSIOUT 380 420 850 1000 0 0 9 13 0 4 13 -- -- -- -- -- -- -- -- -- -- -- 650 700 1200 1300 2 3 13 16 2 8 15 mV mV mV mV
19.4 Transmitter: RF Parameters
RF parameters assume a matching network between test equipment and the D.U.T, and apply to all bands unless otherwise specified.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 49
Electrical Characteristics Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Limits Parameter Test Conditions Comments Min (FCE, FJE) 4 3.5 2.3 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- OLA[1:0] = 00, RX mode OLA[1:0] = 00, RX mode OLA[1:0] = 00, RX mode OLA[1:0] = 00, RX mode -- -- -- -- -- Min (FCAE, FJAE) 2 1.5 0.3 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Unit Typ 7.25 6.8 5.7 5.8 0 6 12 25 -33 -32 -50 -54 -41 -49 -53 -58 -54 -57 -56 -57 3 2500 2100 1300 1200 310 Max 11 10 10 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- dBm dBm dBm dBm dB dB dB dB dBc dBc dBc dBc dBc dBc dBc dBc dBm dBm dBm dBm s
4.1 Output power at 315 MHz 4.16 Output power at 434 MHz 4.2 Output power at 868 MHz 4.25 Output power at 916 MHz 4.20 Output power attenuation 4.3 4.4 4.5 4.10 Harmonic 2 level at 315 MHz 4.17 Harmonic 2 level at 434 MHz 4.11 Harmonic 2 level at 868 MHz 4.20 Harmonic 2 level at 916 MHz 4.12 Harmonic 3 level at 315 MHz 4.18 Harmonic 3 level at 434 MHz 4.13 Harmonic 3 level at 868 MHz 4.21 Harmonic 3 level at 916 MHz
OLA[1:0] = 00, VCC = 3.0 V, TA = 25C OLA[1:0] = 00, VCC = 3.0 V, TA = 25C OLA[1:0] = 00, VCC = 3.0 V, TA = 25C OLA[1:0] = 00, VCC = 3.0 V, TA = 25C OLA[1:0] = 00 OLA[1:0] = 01 OLA[1:0] = 10 OLA[1:0] = 11 OLA[1:0] = 00 OLA[1:0] = 00 OLA[1:0] = 00 OLA[1:0] = 00 OLA[1:0] = 00 OLA[1:0] = 00 OLA[1:0] = 00 OLA[1:0] = 00
4.30 Spurious level at 315 MHz Fref OLA[1:0] = 00 4.14 Spurious level at 434 MHz Fref OLA[1:0] = 00 4.15 Spurious level at 868 MHz Fref OLA[1:0] = 00 4.31 Spurious level at 916 MHz Fref OLA[1:0] = 00 4.6 Output rise/fall time 4.7 RFOUT parallel resistance at 315 MHz 4.71 RFOUT parallel resistance at 434 MHz 4.72 RFOUT parallel resistance at 868 MHz 4.73 RFOUT parallel resistance at 916 MHz
4.8 RFOUT optimum load resistance OLA[1:0] = 00, TX mode at 315 MHz
MC33696 Data Sheet, Rev. 9 50 Freescale Semiconductor
Electrical Characteristics Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Limits Parameter Test Conditions Comments Min (FCE, FJE) -- -- -- -- Min (FCAE, FJAE) -- -- -- -- Unit Typ 310 310 310 1 Max -- -- -- -- pF
4.81 RFOUT optimum load resistance OLA[1:0] = 00, TX mode at 434 MHz 4.82 RFOUT optimum load resistance OLA[1:0] = 00, TX mode at 868 MHz 4.83 RFOUT optimum load resistance OLA[1:0] = 00, TX mode at 916 MHz 4.9 RFOUT parallel capacitance Receive and transmit modes
Output Power Variation vs Temperature (Ref : 25C, 3V) 0.6 0.5 Output Power Variation (dB) 0.4 0.3 0.2 0.1 0 315 MHz 434 MHz 868 MHz 916 MHz
-0.1 -0.2 -0.3 -40C
25C Temperature (C)
85C
Figure 43. Output Power Versus Temperature
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 51
Electrical Characteristics
Output Power Variation vs Voltage (Ref : 3V, 25C) 0.4 0.2 Output Power Variation (dB) 0 -0.2 -0.4 315 MHz -0.6 -0.8 -1 2.1 V 434 MHz 868 MHz 916 MHz
2.4 V Voltage (V)
3V
3.6 V
Figure 44. Output Power Versus Supply Voltage
19.5 PLL & Crystal Oscillator
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Parameter 5.9 PLL lock time 5.1 Toggle time between 2 frequencies 5.21 Occupied bandwidth @ 99% 5.22 5.23 5.24 5.10 Crystal oscillator startup time 5.8 Crystal series resistance Test Conditions Comments RF frequency 25kHz RF frequency step <1.5MHz, RF frequency 25kHz OOK 1.2 kbps OOK 19.2 kbps FSK 128 kHz, 1.2 kbps FSK 128 kHz, 19.2 kbps Limits Unit Min -- -- -- -- -- -- -- -- Typ 50 30 58 248 160 278 0.6 -- Max 100 -- -- -- -- -- 1.2 120 s s kHz kHz kHz kHz ms
MC33696 Data Sheet, Rev. 9 52 Freescale Semiconductor
Electrical Characteristics
19.6 Strobe Oscillator (SOE = 1)
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Parameter 6.1 Period range 6.2 External capacitor C3 6.3 Sourced/sink current 6.4 High threshold voltage 6.5 Low threshold voltage 6.6 Overall timing accuracy With 1% resistor R13 & 5% capacitor C3, 3 sigma variations With 1% resistor R13 Test Conditions Comments TStrobe = 106.C3 Limits Unit Min 0.1 0.1 -- -- -- -14.2 Typ -- -- 1 1 0.5 -- Max -- 10 -- -- -- 15.8 ms nF A V V %
19.7 Digital Input: CONFB, MOSI, SCLK, SEB, STROBE, RSSIC
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Parameter 7.7 Input low voltage 7.8 Input high voltage 7.9 Input hysteresis 7.10 Input low voltage 7.11 Input high voltage 7.12 Input hysteresis 7.5 Sink current 7.6 Configuration, receive, transmit modes standby or LVD modes CONFB, STROBE2 Test Conditions Comments MOSI, SCLK, SEB, RSSIC(1) Limits Unit Min -- 0.8 x VCC2 0.1 x VCC2 -- 0.8 x VCCDIG2 0.1 x VCCDIG2 1 0.5 Typ -- -- -- -- -- -- -- -- Max 0.4 x VCC2 -- -- 0.4 x VCCDIG2 -- -- 100 10 V V V V V V nA nA
NOTES: 1 Input levels of those pins are referenced to VCC2 which depends upon VCC (see Section 6, "Power Supply"). 2 Input levels of those pins are referenced to V CCDIG2 which depends upon the circuit state (see Section 6, "Power Supply").
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 53
Electrical Characteristics
19.8 Digital Output
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Parameter Test Conditions Comments Limits Unit Min Typ Max
Digital Output: DATACLK, LVD, MISO, MOSI, SCLK 8.1 Output low voltage 8.2 Output high voltage 8.3 Fall and rise time From 10% to 90% of the output swing, CLOAD = 10pF |ILOAD| = 50 A -- 0.8 x VCCIO -- -- -- 80 0.2 x VCCIO -- 150 V V ns
Digital Output: SWITCH (VCC = 3V) 8.4 Output low voltage 8.5 Output high voltage |ILOAD| = 50 A -- 0.8 x VCC -- -- 0.2 x VCC -- V V
19.9 Digital Interface Timing
Operating supply voltage and temperature range see Table 3. Values refer to the circuit recommended in the application schematic (see Figure 47), unless otherwise specified. Typical values reflect average measurement at VCC = 3.0 V, TA = 25C. Parameter 9.2 SCLK period 9.8 Configuration enable time 9.3 Enable lead time If crystal oscillator is running, if not see page 15 for entering into configuration Test Conditions Comments Limits Unit Min 1 20 3 x Tdigclk Typ -- -- -- Max -- -- -- s s ns
9.4 Enable lag time 9.5 Sequential transfer delay 9.6 Data hold time 9.7 Data setup time 9.9 9.10 Data setup time Receive mode, DME = 1, from SCLK to MOSI Configuration mode, from SCLK to MISO Configuration mode, from SCLK to MOSI Configuration mode, from SCLK to MOSI
100 100 3 x Tdigclk -- 120 100
-- -- -- -- -- --
-- --
1
ns ns s ns ns ns
-- 100 -- --
NOTES: 1 The digital interface can be used in SPI burst protocol, i.e., with a continuous clock on SCLK port. For example, one (or more) read access followed by one (or more) write access and so on. In this case and for a practical use, the pulse required on CONFB between accesses must be less than one digital clock period Tdigclk.
MC33696 Data Sheet, Rev. 9 54 Freescale Semiconductor
Electrical Characteristics
SEB
9.8
CONFB
9.3 9.4 9.5
SCLK (input)
9.2 9.10 9.9
MOSI (input)
9.7
MISO (output)
Figure 45. Digital Interface Timing Diagram in Configuration Mode
SEB
CONFB
SCLK (input)
9.3
9.6
MOSI (output)
Figure 46. Digital Interface Timing Diagram in Receive Mode (DME = 1)
Examples of crystal characteristics are given in Table 25.
Table 25. Typical Crystal Reference and Characteristics
Reference & Type 315 MHz Parameter Frequency Load capacitance ESR LN-G102-1183 NX5032GA 17.5814 8 25 434 MHz LN-G102-1182 NX5032GA 24.19066 8 15 868 MHz EXS00A-01654 NX5032GA 24.16139 8 <70 Unit MHz pF
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 55
Application Schematics
20
Application Schematics
C3 1 nF RSSIOUT STROBE VCC2 C7 SWITCH C8 5V GND 32 31 30 29 28 27 26 25 GNDIO
VCC2IN
GNDSUBD
STROBE
SWITCH
VCC2 VCCINOUT C28 C6 J1 SMA Vert L10 L7 C39 C36 C40 C22 VCC2 C20
VCCIN
GND
NC
1 2 3 4 5 6 7 8
RSSIOUT VCC2RF RFIN GNDLNA VCC2VCO GNDPA1 RFOUT
SEB SCLK MOSI
24 23 22 21 20 19 18 17
SEB SCLK MOSI MISO CONFB DATACLK RSSIC
U4 MC33696
MISO CONFB DATACLK RSSIC
VCC2OUT
VCCDIG2
XTAL0UT
VCCDIG
GNDPA2 XTALIN
VCCINOUT
GNDDIG RBGAP GND R13
9
10
11
12
13
14
15
C24 X1 C29
VCC2 C30 C31
C35
Figure 47. MC33696 Application Schematic (5 V)
20.1 PCB Design Recommendations
Pay attention to the following points and recommendations when designing the layout of the PCB. * Ground Plane -- If you can afford a multilayer PCB, use an internal layer for the ground plane, route power supply and digital signals on the last layer, RF components being located on the first layer. -- Use at least a double-sided PCB. -- Use a large ground plane on the opposite layer. -- If the ground plane must be cut on the opposite layer for routing some signals, maintain continuity with another ground plane on the opposite layer and a lot of via to minimize
MC33696 Data Sheet, Rev. 9 56 Freescale Semiconductor
16
Application Schematics
*
*
parasitic inductance. Power Supply, Ground Connection and Decoupling -- Connect each ground pin to the ground plane using a separate via for each signal; do not use common vias. -- Place each decoupling capacitor as close to the corresponding VCC pin as possible (no more than 2-3 mm away). -- Locate the VCCDIG2 decoupling capacitor (C13) directly between VCCDIG2 (pin 14) and GND (pin 16). -- GNDPA1 and GNDPA2 inductance to ground should be minimum. If possible, use two via for each pin. RF Tracks, Matching Network and Other Components -- Minimize any tracks used for routing RF signals. -- Locate crystal X1 and associated capacitors C15 and C11 close to the MC33696. Avoid loops occurring due to component size and tracks. Avoid routing digital signals in this area. -- Use high frequency coils with high Q values for the frequency of operation (minimum of 15). Validate any change of coil source. -- Track between RFOUT and RFIN should be as short as possible to minimize lost in TX mode. NOTE The values indicated for the matching network have been computed and tuned for the the MC33696 RF Modules available for MC33696 evaluation. Matching networks should be retuned if any change is made to the PCB (track width, length or place, or PCB thickness, or component value). Never use, as is, a matching network designed for another PCB.
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 57
Case Outline Dimensions
21
Case Outline Dimensions
21.1 LQFP32 Case
MC33696 Data Sheet, Rev. 9 58 Freescale Semiconductor
Case Outline Dimensions
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 59
Case Outline Dimensions
MC33696 Data Sheet, Rev. 9 60 Freescale Semiconductor
Case Outline Dimensions
21.2 QFN32 Case
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 61
Case Outline Dimensions
MC33696 Data Sheet, Rev. 9 62 Freescale Semiconductor
Case Outline Dimensions
MC33696 Data Sheet, Rev. 9 Freescale Semiconductor 63
How to Reach Us:
Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Document Number: MC33696 Rev. 9 06/2007
Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2006, 2007. All rights reserved. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp.

▲Up To Search▲

Price & Availability of MC33696

	To Download MC33696 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .